総合カタログVer6.0

189/702

センタンツールの仕様変更については別途ご相談下さい。／都合により予告なく仕様を変更することがあります。Please do not hestiate to contact us if you have any request for a special production. / Specification is subject to change without notice.186詳しい説明 For further informationページ Page183 ～ 186Non-Metal Material Metal Material Non-Ferrous MetalApplicable MaterialsCarbon Tool SteelSK＊＊HardHB481～HRC50～▲●High-Speed Tool SteelSKH＊＊▲●Alloy Tool SteelSKS＊＊▲●Martensitic Stainless SteelSUS440A～C・F▲●Nickel Chrome SteelSNC＊＊HB286～480HRC30～49▲▲▲▲●●●Nickel-Chrome-Molybdenum Steel SNCM＊＊＊▲▲▲▲●●●Chrome steelSCr＊＊▲▲▲▲●●●Chrome Molybdenum Steel SCM＊＊＊▲▲▲▲●●●Manganese Steel SMh＊＊＊▲▲▲▲●●●Manganese Chromium SteelSMnC＊＊＊▲▲▲▲●●●Precipitation Hardening Stainless SteelSUS6＊＊▲▲▲▲●●●Carbon Steels for Machine Structural Use S＊＊CSoftHB226～381HRC20～40●●●●●●●Nickel Chrome SteelSNC＊＊●●●●●●●Heat Resistant Steel SUH＊＊＊●●●●●●●Gray IronFC＊＊＊●●●●●●●Aluminium Chrome Molybdenum Steel SACM＊＊＊●●●●●●●Martensitic Stainless Steel SUS4＊＊●●●●●●●Austenitic Stainless SteelSUS3＊＊●●●●●●●Austenitic-Ferritic Stainless SteelSUS329J1●●●●●●●Rolled Steels for General Structural UseSS＊＊＊Less than HB226Less than HRC20●●●●▲●●▲▲Carbon Steels for Machine Structural UseS＊＊C●●●●▲●●▲▲Heat Resistant Steel SUH＊＊＊Annealing●●●●▲●●▲▲Gray IronFC＊＊＊●●●●▲●●▲▲Austenitic Stainless Steel SUS3＊＊●●●●▲●●▲▲Ferritic Stainless Steel SUS4＊＊●●●●▲●●▲▲Rolled Steels for General Structural UseSS＊＊＊－●●●▲▲▲▲▲▲Carbon Steels for Machine Structural UseS＊＊CAnnealing●●●▲▲▲▲▲▲Cemented Carbide Super HardCermetSuper HardBeryllium Copper (Alloy 25)BeCu25Hard▲▲▲▲▲▲▲Titaniumα β　α-βHard▲▲▲▲▲▲▲Hastelloy Hard▲▲▲▲▲▲▲Phosphor BronzePB＊Hard▲▲▲▲▲▲▲Inconel Alloy Soft▲▲●▲▲●●Beryllium Copper (Alloy 50)BeCu50Soft▲▲●▲▲●●Aluminium Bronze ABB＊Soft▲▲●▲▲●●Pure TitaniumSoft▲▲●▲▲●●MonelBC＊Soft▲▲●▲▲●●Bronze BS＊Soft▲▲●▲▲●●Brass Soft▲▲●▲▲●●AluminiumA＊＊＊＊Soft▲▲●▲▲●●CeramicsSuper HardSiliconSuper HardFerriteSuper HardQuartz GlassSuper HardStoneSuper HardResinSuper Soft●●●Rubber Super Soft●●●WoodSuper Soft●●●General Notes・Before using tools, make sure to check there is no flaw and crack.・Use tools with proper rotation speed.・Do not use tools with any runout grinders. It may cause damage and fall of durability of tools.・According to our reports, cutters being broken is attributed to using with the grinders not rotating properly. It may cause damage to tools and less durability. ・Please wear eye protection while working.・Please mount tools with care of overhanging; it should be within 13mm.　Compatible table of cuttersand materialsCarbideH.S.SSteel■Reference for overhangingOverhanged length of shank（mm）Allowable Rotation Speed of Tools（as a guide）20×30×40×

※このページを正しく表示するにはFlashPlayer10.2以上が必要です